Metabo W 720-115 Operations Instructions download pdf (Page 9)

ENGLISH en

n.............. rated speed

See page 2.

1 Support flange

2Spindle

3 Spindle locking button

4 Sliding

on/off switch

5 Trigger *

6Switch-on lock *

7 Additional handle

8Safety cover

9 Clamping nut

10 2-hole spanner

11 Clamping ring

12 Clamping screw

* depending on equipment/not in scope of delivery

Before plugging in, check to see that the rated

mains voltage and mains frequency,

as stated on the rating label, match your power

supply.

5.1 Attaching the additional handle

Always work with the additional handle

attached (7)! Attach the additional handle

on the left or right of the machine and secure.

5.2 Install safety guard

For safety reasons, always use the safety

guard provided for the respective wheel! See

also chapter 9.

Safety guard for grinding

Designed for work with roughing wheels, flap

sanding pads, diamond cut-off wheels.

See page 2, illustration C.

- Loosen the clamping screw (12) until the clamping

ring (11) on the safety guardexpands sufficiently.

- Place the safety guard (8) in the position

indicated.

- Turn the safety guard until the closed section is

facing the operator.

- Tighten the clamping screw (12) firmly. Make sure

that the guard is seated securely - you should not

be able to turn the safety guard (8).

Use only accessories that

are covered by at least

3.4 mm by the safety guard.

Disconnect the mains plug before changing

any accessories. The machine must be

switched off and the spindle at a standstill.

For reasons of safety, attach the parting guard

before performing parting work

(see chapter 9. Accessories).

6.1 Locking the spindle

- Press in the spindle locking button (3) and turn the

spindle (2) by hand until the spindle locking button

engages.

6.2 Placing the grinding wheel in position

See illustration A on page 2.

- Place the supporting flange (1) on the spindle. The

flange should not turn on the spindle when

properly attached.

- Place the grinding wheel on the support flange (1).

The grinding wheel must lay flat on the supporting

flange. The metal flange on the parting grinder

disc must lay flat on the support flange.

6.3 Securing/Releasing the clamping nut

Securing the clamping nut (9):

The 2 sides of the clamping nut are different. Screw

the clamping nut onto the spindle as follows:

See illustration B on page 2.

- A) For thin grinding wheels:

The edge of the clamping nut (9) faces upwards

so that the thin grinding wheel can be attached

securely.

B) For thick grinding wheels:

The edge of the clamping nut (9) faces

downwards so that the clamping nut can be

attached securely to the spindle.

- Lock the spindle. Turn the clamping nut (9)

clockwise using the 2-hole spanner (10) to

secure.

Releasing the clamping nut:

- Lock the spindle (see chapter 6.1). Turn the

clamping nut (9) anticlockwise using the 2-hole

spanner (10) to unscrew.

7.1 Switching On and Off

Always guide the machine with both hands.

Switch on first, then guide the

accessory

towards the workpiece.

The machine must not be allowed to draw in

additional dust and shavings. When switching

the machine on and off, keep it away from dust

deposits. After switching off the machine, only place

it down when the motor has come to a standstill.

Avoid inadvertent starts: always switch the

tool off when the plug is removed from the

mains socket or if there has been a power cut.

In continuous operation, the machine

continues running if it is forced out of your

hands. Therefore, always hold the machine with

both hands using the handles provided, stand in a

safe position and concentrate.

4. Overview

5. Commissioning

6. Attaching the grinding wheel

7. Use

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 27 28

Comments to this Manuals

No comments

Metabo W 720-115 Operations Instructions Page 9

Comments to this Manuals

Related products and manuals for Power tools Metabo W 720-115