Metabo H 16-500 Use and Care Manual download pdf (Page 7)

ENGLISH

ENG

6 Buttons for setting the temperature*

7 Buttons for setting the air volume*

8 Program selection button*

9 Display* (for temperature and speed)

10 Save button* (for saving changed programs)

11 Adjusting wheel for setting the temperature*

* depending on the features / model

Before plugging in, check that the rated

mains voltage and mains frequency, as

stated on the rating label, match with your power

supply.

The distance to the object being processed

depends on the material and intended

processing type. Always first carry out an inspec-

tion of air volume and temperature! The attachable

nozzles (see chapter 8) available as accessories

can be used for precise hot air control to a specific

point or a surface.

Take care when changing hot nozzles!

Danger of burns.

5.1 H 16-500

The sliding switch (4) can be used to switch the

tool on and off and for selecting between 2 stages

(for air volume and temperature).

Stage 1

: 750 °F, 8.5 cf/min

Stage 2

: 1100 °F, 14.8 cf/min

5.2 HE 20-600

The sliding switch (4) can be used to switch the

tool on and off and for selecting between 3 stages.

The air volume is varied in the three stages from

3.6/10.6/15.0 cf/min.

stage 1

of the sliding switch (4) the temperature

is always 120 °F (cold-air stage). Use the cold-air

stage to dry paint, cool workpieces or to cool

down the nozzle before changing an accessory

part.

stage 2 and 3

of the sliding switch (4) the

temperature can be set steplessly at the adjusting

wheel (11).

The numbers 1 - 9 shown on the adjusting wheel

are used for orientation. "1" means 120 °F. "9"

means 1100 °F (maximum temperature).

5.3 HE 23-650 Control

The sliding switch (4) can be used to switch the

tool on and off and for selecting between 2 stages.

Setting temperature:

stage 1

of the sliding switch (4) the temperature

is always 120 °F (cold-air stage). Use the cold-air

stage to dry paint, cool workpieces or to cool

down the nozzle before changing an accessory

part.

stage 2

of the sliding switch (4) the temperature

can be set steplessly.

Press the buttons (6) to set the temper-

ature.

Briefly press the "+" /"-" buttons to

increase or lower the set value in 10°F

steps. Press the buttons longer to change the

value faster.

Notes:

Triangles are displayed when

the desired temperature is

being set.

If the desired temperature is

set, the blower (depending

on the selected speed/air

volume) needs a few seconds to reach the set

value. The triangles flash during this period.

The actual temperature is

measured at the nozzle

outlet. The triangles disap-

pear when the desired temperature has been

reached.

When the heat gun is switched off, the last value

set is retained.

Setting air volume:

Press the buttons (7) to set the air

volume or the fan speed.

Program operation:

Four programs for the most frequent types

of work are set in the factory. Press the "

button for program operation. A for

program 1 appears in the display. Press the

program button again to reach the

programs , and . Press the button again to

return to normal operation.

Program 1: Forming plastic pipes

Program 2: Welding plastic pipes

Program 3: Removing paint

Program 4: Soft soldering

(For technical data, see chapter 11)

Changing programs and saving:

The values in the four programs can be

changed and saved. To do this, first press

the program button "

" until the program to

be changed is displayed. Set the desired air

volume and temperature. Then push the

save button (10) until the symbol in the display

5Use

17027019_0111 HE 23-650 HE 20-600 H 16-500 NAFTA.book Seite 7 Dienstag, 25. Januar 2011 4:36 16

1 2 3 4 5 6 7 8 9 10 11 12 ... 31 32

Comments to this Manuals

No comments

Metabo H 16-500 Use and Care Manual Page 7

Comments to this Manuals

Related products and manuals for Power tools Metabo H 16-500