Metabo H 16-500 Use and Care Manual download pdf (Page 6)

ENGLISH

ENG

Double Insulated Tools

Tools

marked with the words “Double Insulated”

are equipped with a two prong plug.These tools

have a special insulation system that complies

with applicable UL standards. They do not require

grounding. ”Double Insulated” tools, like this one,

have two prong cords and can use either a two or

three prong extension cord.

“This appliance has a polarized plug (one blade is

wider than the other). To reduce the risk of electric

shock, this plug is intended to fit in a polarized

outlet only one way. If the plug does not fit fully in

the outlet, reverse the plug. If it still does not fit,

contact a qualified electrician. Do not modify the

plug in any way.”

Extension Cords

As the distance from the supply outlet increases,

heavier gauge extension cords are required. The

use of extension cords of inadequate size wire

causes a serious drop in voltage and loss of

power. Protect the cord from damage. Keep cords

away from excessive heat, sharp edges and damp

or wet areas. Repair or replace damaged

extension cords before using.

Ext. Cord Length Wire Size

040 Ft.................... 16

085 Ft.................... 14

100 Ft.................... 12

170 Ft.................... 10

270 Ft.....................8

400 Ft.....................6

650 Ft.....................4

For your own protection and for the

protection of your power tool, pay

attention to all parts of the text that are

marked with this symbol!

Never look inside the outlet tube!

Never use the heat gun for drying your hair!

Always wear goggles and workgloves!

Take special care when using the heat gun near

combustible materials or explosive gases.

Children should be supervised to ensure that they

do not play with the tool.

Risk of burns: Never touch the hot outlet tube.

Never use power tools when damp, or in a damp

or wet environment.

Take special care when using tools near combus-

tible materials. Never direct at the same point for

long periods.

Heat can be directed to concealed combustible

materials.

Never direct the heat gun at highly flammable

materials! Fires can be caused if the heat gun is not

used with great care.

Never leave the tool unattended when it is running.

After long periods of use at maximum temperature,

the temperature should be lowered before the tool

is switched off. This lengthens the service life of

the heater.

Place the tool on the bases provided following use

and wait until it has cooled down before placing in

storage!

Store your tools in a safe place.

Unused tools should be stored in a dry, locked

room inaccessible to children.

Always take care where there are toxic gases and

a risk of explosion.

Toxic can be created when working on plastics,

paints and similar materials. Risk of fire and

combustion!

Only use the heat gun in well-ventilated rooms!

Never inhale the vapours created!

For your own safety, only use accessories and

auxiliary devices specified in the Operating

Instructions or recommended or specified by the

tool manufacturer. The use tools or accessories

other than those recommended in the Operating

Instructions or in the catalogue can result in a risk

of injury.

Symbols on the tool:

...........Class II Construction

V ...............volts

A...............amperes

W..............watts

Hz.............hertz

~ ...............alternating current

See page 2.

1 Stainless steel outlet tube

2 Detachable protective tube (for areas that are

difficult to access)

3 Air inlet with grid (keeps foreign bodies out)

Sliding switch (

On-Off switch/stepping

switch)

5 Anti-slip bases (for non-tilting and anti-slip

stationary work applications)

3 Special Safety Instructions

4Overview

17027019_0111 HE 23-650 HE 20-600 H 16-500 NAFTA.book Seite 6 Dienstag, 25. Januar 2011 4:36 16

1 2 3 4 5 6 7 8 9 10 11 ... 31 32

Comments to this Manuals

No comments

Metabo H 16-500 Use and Care Manual Page 6

Comments to this Manuals

Related products and manuals for Power tools Metabo H 16-500