Metabo WE 14-150 Plus Operations Instructions download pdf (Page 12)

ENGLISHen

Original instructions

We, being solely responsible, hereby declare that

these angle grinders conform to the standards and

directives specified on page 3.

The angle grinders, when fitted with original Metabo

accessories, are suitable for grinding, sanding,

separating and wire brushing metal, concrete,

stone and similar materials without the use of water.

WE 14-125 VS is also suitable for polishing.

The user bears sole responsibility for any damage

caused by improper use.

Generally accepted accident prevention regula-

tions and the enclosed safety information must be

observed.

For your own protection and for the

protection of your electrical tool, pay

attention to all parts of the text that are

marked with this symbol!

WARNING – Reading the operating instruc-

tions will reduce the risk of injury.

WARNING Read all safety warnings and

instructions. Failure to follow all safety warn-

ings and instructions may result in electric shock,

fire and/or serious injury.

Keep all safety instructions and information for

future reference. Pass on your electrical tool only

together with these documents.

4.1 Safety Warnings Common for Grinding,

Sanding, Wire Brushing or Abrasive

Cutting-Off Operations:

Use

a) This power tool is intended to function as a

grinder, sander, wire brush or cut-off tool. Read

all safety warnings, instructions, illustrations

and specifications provided with this power

tool. Failure to follow all the instructions may result

in electric shock, fire and/or serious injury.

WE 14-125 VS may also be used as a polisher.

b) Operations such as polishing are not

recommended to be performed with this power

tool. Operations for which the power tool was not

designed may create a hazard and cause personal

injury. (This does not apply to WE 14-125 VS.)

c) Do not use accessories which are not

specifically designed and recommended by the

tool manufacturer. Just because the accessory

can be attached to your power tool, it does not

assure safe operation.

d) The rated speed of the accessory must be at

least equal to the maximum speed marked on

the power tool. Accessories running faster than

their rated speed can break and fly apart.

e) The outside diameter and the thickness of

your accessory must be within the capacity

rating of your power tool. Incorrectly sized

accessories cannot be adequately guarded or

controlled.

f) The arbour size of wheels, flanges, backing

pads or any other accessory must properly fit

the spindle of the power tool. Accessories with

arbour holes that do not match the mounting

hardware of the power tool will run out of balance,

vibrate excessively and may cause loss of control.

g) Do not use a damaged accessory. Before

each use inspect the accessory such as

abrasive wheels for chips and cracks, backing

pad for cracks, tear or excess wear, wire brush

for loose or cracked wires. If power tool or

accessory is dropped, inspect for damage or

install an undamaged accessory. After

inspecting and installing an accessory,

position yourself and bystanders away from

the plane of the rotating accessory and run the

power tool at maximum no-load speed for one

minute.

Damaged accessories will normally break

apart during this test time.

h) Wear personal protective equipment.

Depending on application, use face shield,

safety goggles or safety glasses. As

appropriate, wear dust mask, hearing

protectors, gloves and a workshop apron

capable of stopping small abrasive or

workpiece fragments. The eye protection must

be capable of stopping flying debris generated

by various operations. The dust mask or

respirator must be capable of filtrating particles

generated by your operation. Prolonged exposure

to high intensity noise may cause hearing loss.

i) Keep bystanders a safe distance away from

work area. Anyone entering the work area must

wear personal protective equipment. Fragments

of workpiece or of a broken accessory may fly away

and cause injury beyond immediate area of

operation.

j) Hold power tool by insulated gripping

surfaces only, when performing an operation

where the cutting accessory may contact

hidden wiring or its own cord. Cutting accessory

contacting a "live" wire may make exposed metal

parts of the power tool "live" and could give the

operator an electric shock.

k) Position the cord clear of the spinning

accessory. If you lose control, the cord may be cut

or snagged and your hand or arm may be pulled into

the spinning accessory.

I) Never lay the power tool down until the

accessory has come to a complete stop. The

spinning accessory may grap the surface and pull

the power tool out of your control.

1. Conformity Declaration

2. Specified Use

3. General Safety Instructions

4. Special Safety Instructions

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 107 108

Comments to this Manuals

No comments

Metabo WE 14-150 Plus Operations Instructions Page 12

Comments to this Manuals

Related products and manuals for Power tools Metabo WE 14-150 Plus