Metabo KHE-D 28 Operations Instructions Page 6
- Page / 18
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
ENGLISHen
6
For continuous operation the trigger can be locked
with the lock button (10). To stop the machine,
press the trigger again.
If switched on continuously, the machine
continues running if it is jerked out of
your hands. Therefore, always hold the
machine with both hands on the handles, stand
safely, and concentrate on your work.
6.3 Operating mode selection
Select the desired operating mode by turning the
control knob (13). To turn, push the stop (12).
twist drilling
hammer drilling
(only with use of hammer drill chuck)
chiselling
(KHE-D 28,
KHE-D 24
)
In chisel mode the chisel is locked to be twist-proof.
To position the chisel for the particular application,
set the control knob (13) between and
.
When a chisel is fitted, only operate the
machine in the chiselling operating
mode.
Avoid levering movements of the
machine when a chisel is fitted.
6.4 Selection of direction of rotation
Do not actuate the rotation selector
switch (9) unless the motor has
completely stopped.
Select direction of rotation:
R=clockwise
L = counter-clockwise
6.5 Drill chuck change (not KHE-D 24,
BHE-D 24)
When changing chucks make sure that
the spindle is clean. Grease spindle
lightly if required.
Removing the chuck:
Turn chuck lock (5) in direction indicated by arrow
against the stop (a) and pull it off the spindle (b).
Replacing the chuck:
Place chuck onto spindle (6) (a). Turn chuck lock (5)
in direction indicated by arrow (b) until chuck slides
fully onto the spindle, then release the chuck lock.
Check to see that the chuck is properly seated.
Note: To keep the spindle from turning while
changing chucks, set the control knob (13) to
chiselling.
6.6 Tool Change with SDS Chuck
Before fitting, clean tool shank and apply
special grease! Use only SDS-Plus tools!
Inserting the tool:
Turn the tool while inserting, until it engages. The
tool is automatically locked.
Removing the tool:
Turn tool lock (3) in direction indicated by arrow (a)
and remove the tool (b).
6.7 Tool change with Futuro Plus keyless
chuck (not KHE-D 24, BHE-D 24)
Insert tool. Grip the retaining ring (a) firmly and, with
the other hand, turn sleeve (b) towards "GRIP, ZU",
until the mechanical resistance which can be felt is
overcome.
- BHE-D 24 1
- KHE-D 24 1
- KHE-D 28 1
- Postfach 1229 3
- Metabo-Allee 1 3
- D-72622 Nürtingen 3
- Operating Instructions 4
- ENGLISH en 5
- 3. Specific Safety Rules 5
- 4. Functional Description 5
- 5. Assembly, Initial Use 5
- 6. Operation 5
- ENGLISHen 6
- Mode d’emploi 8
- FRANÇAIS fr 9
- 3. Consignes de sécurité 9
- 4. Vue d'ensemble 9
- FRANÇAISfr 10
- 5. Mise en service 10
- 6. Utilisation 10
- Instrucciones de manejo 13
- ESPAÑOLes 14
- 4. Vista de conjunto 14
- ESPAÑOL es 15
- 5. Puesta en marcha 15
- 6. Manejo 15
- 7. Consejos y trucos 16
- 8. Mantenimiento 16
- Metabowerke GmbH 18
- 72622 Nürtingen, Germany 18
- 170 24 9670 - 0912 18
Related products and manuals for Power drills Metabo KHE-D 28
(23 pages)
(40 pages)Acoustic Energy AE32-140 podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Głośniki Acoustic Energy AE32-140.
Dostarczamy 1 pdf podręczników Acoustic Energy AE32-140 do pobrania za darmo według typów dokumentów: Arkusz Danych
Comments to this Manuals