Metabo SE12-115 Use and Care Manual download pdf (Page 9)

ENGLISH en

- Press in spindle locking button (8) and hold in

place.

- Screw the tool fixing screw (15) onto the

tensioning spindle and tighten (the spindle locking

knob engages and the tool can be secured).

If the tools used are shorter than the

tensioning spindle, insert the relevant distance

sleeves (18). This is the only way to properly secure

the tool.

Disconnect the mains plug or remove the battery

pack from the machine before starting any mainte-

nance work.

Motor cleaning: blow compressed air through the

rear ventilation slots of the machine regularly,

frequently and thoroughly. Here, the machine must

be held firmly.

Mains powered machines: The Autostop carbon

brushes must only be replaced in a specialist work-

shop. Always have checks and maintenance work

carried out by Metabo Customer Service.

9.1 Mains powered machines

- Electronic restart protection

The red electronic signal indicator (2) starts

flashing. If the mains plug is inserted with the

machine switched on, or if the current supply is

restored following an interruption, the machine

does not start up. Switch the machine off and then

back on again.

- The electronic signal indicator (2) lights up

and on-load speed is reduced.

Winding temperature too high. Run the machine in

idling until the electronics signal indicator

switches off.

- High-energy, high-frequency interference

High-energy, high-frequency interference can

cause the machine to deactivate. In this case,

please switch off the machine, disconnect the

plug and then reinsert. As soon as the interference

is reduced, you can continue work.

9.2 Cordless machines

- The electronic signal display (2) lights up and

the load speed decreases. The temperature is

too high! Run the machine in idling until the elec-

tronics signal indicator switches off.

- The electronic signal display (2) flashes and

the machine does not start. The restart protec-

tion is active. The machine will not start if the

battery pack is inserted while the machine is on.

Switch the machine off and on again.

Use only genuine Metabo accessories.

Use only accessories that fulfil the requirements

and specifications listed in these operating instruc-

tions.

For a complete range of accessories, see

www.metabo.com or the catalogue.

Repairs to electrical tools must be carried out

by qualified electricians ONLY!

If you have Metabo electrical tools that require

repairs, please contact your Metabo service centre.

For addresses see www.metabo.com.

You can download spare parts lists from

www.metabo.com.

Observe national regulations on environmentally

compatible disposal and on the recycling of disused

machines, packaging and accessories.

Special instructions for cordless machines:

Battery packs must not be disposed of with regular

waste. Return faulty or used battery packs to your

Metabo dealer!

Do not allow battery packs to come into contact with

water!

Before disposal, discharge the battery pack in the

power tool. Prevent the contacts from short-

circuiting (e. g. by protecting them with adhesive

tape).

Explanation of details on page 3. Subject to

changes serving technical progress.

D =Permitted wheel diameter

max

=Maximum wheel width

M=Spindle thread

l=Length of spindle

n =No-load speed (maximum speed)

U =Voltage of battery pack

120 V

=Current at 120 V

=Nominal power input

=Power output

m =Weight with smallest battery pack/weight

without cord

The technical specifications quoted are subject to

tolerances (in compliance with the relevant valid

standards).

Wear ear protectors!

8. Maintenance

9. Troubleshooting

10. Accessories

11. Repairs

12. Environmental Protection

13. Technical specifications

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 23 24

Comments to this Manuals

No comments

Metabo SE12-115 Use and Care Manual Page 9

Comments to this Manuals

Related products and manuals for Power tools Metabo SE12-115