Metabo SE12-115 Use and Care Manual download pdf (Page 8)

ENGLISHen

Handle bar

The handle bar (9) must be fitted as far as the

limit stop on the gearbox flange.

After releasing the clamping lever (10), the handle

bar (9) can be turned to the desired position. Firmly

tighten the clamping lever (10) again. The position

of the lever might need to be changed for this

purpose.

The position of the lever can be changed without

turning the clamping screw. For this purpose, raise

the lever, turn it and then lower the lever again (see

illustration, page 2).

When working, always position the lever in a

way that it cannot come into contact with the

tool.

Tensioning spindle

Screw the tensioning spindle (10) onto the spindle

(4) while holding in the spindle locking knob (2) and

tighten with an open-ended spanner (12).

5.1 For mains powered machines only

Mains connection

Before plugging in the device, check that the

rated mains voltage and mains frequency, as

specified on the rating label, match your power

supply.

The red electronics signal indicator (7) lights up

briefly when the mains plug is inserted in the socket,

indicating readiness for operation.

Setting speed

The speed can be preset via the setting wheel (14)

and is infinitely variable.

Positions 1-6 correspond approximately to the

following no-load speeds:

1 ........ 900 rpm 4....... 2050 rpm

2 ........ 1250 rpm 5....... 2410 rpm

3 ........ 1660 rpm 6....... 2810 rpm

The VTC electronics make material-compatible

work possible and an almost constant speed, even

under load.

The best way to determine the ideal speed setting is

by performing a test.

5.2 For cordless machines only

Dust filter

Always fit the dust filter if the surroundings are

heavily polluted (1).

The machine heats up faster when the dust

filter is fitted (1). It is protected by the elec-

tronics system from overheating (see chapter9.).

Attaching:

See page 2, illustration A.

Attach dust filter (1) as shown.

To remove:

Holding the dust filter (1) by the upper

edges, raise it slightly and then pull it downwards

and remove.

Rotating battery pack

See illustration B on page 2.

The rear section of the machine can be rotated 270°

in three stages, thus allowing the machine's shape

to be adapted to the working conditions. Only

operate the machine when it is in an engaged posi-

tion.

Battery pack

Charge the battery pack before use (6).

If performance diminishes, recharge the battery

pack.

The ideal storage temperature is between 10°C and

30°C.

"Li-Power" li-ion battery packs have a capacity and

signal indicator: (5)

- Press the button (4), the LEDs indicate the charge

level.

- If one LED is flashing, the battery pack is almost

flat and must be recharged.

Removing and inserting the battery pack

To remove:

Press the battery pack release button

(3) and pull the battery pack (6) downwards.

To fit:

Slide in the battery pack (6) until it engages.

Always guide the machine with both hands.

Switch on first, then guide the

accessory

towards the workpiece.

The machine must not be allowed to draw in

additional dust and shavings. When switching

the machine on and off, keep it away from dust

deposits. After switching off the machine, only place

it down when the motor has come to a standstill.

In continuous operation, the machine

continues running if it is forced out of your

hands. Therefore, always hold the machine with

both hands using the handles provided, stand in a

safe position and concentrate.

Switching on: Push the slide switch (7) forward.

For continuous activation, now tilt downwards until

it engages.

Switching off: Press the rear end of the slide

switch (7) and release.

Press in the spindle locking knob (8) only

when the spindle is stationary!

Tools with threaded insert:

1. Remove the tensioning spindle (16) if neces-

sary. Press in spindle locking button (8) and hold

in place. Unscrew the tensioning spindle using

the open-ended spanner (17).

2. Press in spindle locking button and hold in place.

3. Screw the tool onto the spindle and tighten.

Tools for tensioning spindle:

- Attach the tensioning spindle (16) if necessary.

Press in spindle locking button (8) and hold in

place. Tighten the tensioning spindle using the

open-ended spanner (17).

- Slide the tool onto the tensioning spindle.

6. Switching ON and OFF

7. Installing the tools

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 23 24

Comments to this Manuals

No comments

Metabo SE12-115 Use and Care Manual Page 8

Comments to this Manuals

Related products and manuals for Power tools Metabo SE12-115