Metabo TDP 7500 S User Manual download pdf (Page 9)

ENGLISH

1. Machine Overview ......................8

2. Please Read First!.......................9

3. Range of Application and

Media............................................9

4. Safety...........................................9

4.1 Specified conditions of use ...........9

4.2 General safety instructions ...........9

5. Prior to Operation.......................9

5.1 Discharge hose connection ..........9

5.2 Installation.....................................9

6. Operation...................................10

6.1 Switching ON and OFF...............10

6.2 Pump characteristic curve ..........10

7. Care and Maintenance..............10

7.1 Periodic maintenance .................10

7.2 Pump storage .............................10

8. Trouble Shooting ......................10

8.1 Fault finding ................................10

9. Repairs.......................................11

10. Environmental Protection........11

11. Technical Specifications..........11

x Read these instructions before use.

Pay special attention to the safety

instructions.

x Disregard of the instructions renders

the warranty null and void; the

equipment manufacturer is not liable

for any damage resulting from disre-

gard of the instructions.

x If you notice transport damage while

unpacking, notify your supplier

immediately. Do not operate the

machine!

x Dispose of the packing in an envi-

ronmentally friendly manner. Take

to a proper collecting point.

x Save these instructions - refer to

them when in doubt.

x If you lend or sell this machine be

sure to have the instructions go with

it.

This pump is intended for pumping water

in domestic applications, such as

 pumping containers, sumps and

flooded basements;

 fountain pumps;

 circulation to avoid putrefaction;

 feeding false rivulets and brooks;

 supplying garden irrigation systems.

Caution!

The max. permissible fluid

temperature is 35 °C.

Pumping liquids containing abrasives

(such as sand) reduces the service

life of the pump.

4.1 Specified conditions of

use

This pump must not be used to supply

drinking water or for pumping foodstuff.

Explosive, flammable, aggressive fluids

or substances detrimental to health and

sewage must not be pumped.

This equipment is not suitable for com-

mercial or industrial use.

Any other use is not as specified. Use

not as specified, alteration of the pump

or use of parts that are not approved by

the equipment manufacturer, can cause

unforeseeable damage!

4.2 General safety instruc-

tions

Children, juveniles and persons not fam-

ilar with the instructions are not permit-

ted to operate the pump.

When used in swimming pools and gar-

den ponds and their range of protection,

the regulations according to DIN VDE

0100 -702, -738 are to be observed.

Also all local regulations pertaining to

the safe operation of submersible pumps

are to be observed.

The following residual risks do principally

exist when operating submersible

pumps and can not be fully eliminated –

even by employing safety devices.

Hazard by ambient conditions!

Do not use the pump in hazardous loca-

tions or near inflammable liquids and

gases!

Danger! Risk of electric shock!

Do not touch the plug with wet hands! To

unplug always pull at the plug, not the

power cable.

Connect only to an earthed outlet that is

properly installed, earthed and tested.

Mains voltage and fuse protection must

correspond to those stated in the "Tech-

nical Specications".

Protection must be provided by a resid-

ual current device (RCD) of max. 30 mA

capacity.

Use only extension cables of sufficient

lead cross section (see "Technical Spec-

ifications"). Unroll cable reels fully.

Do not buckle, squeeze, drag or drive

over power cable and extension cables;

protect from sharp edges.

Place extension cable so that it can not

get into the fluid to be pumped.

Always unplug before servicing the

pump.

Danger by pump failings!

Before each use check the pump, espe-

cially the power cable, plug and float

switch for possible damage. Risk of fatal

electric shock!

A damaged pump must be workmanlike

repaired before it can be used again.

Do not attempt to repair the pump your-

self! When repaired inexpertly there is a

hazard of fluid entering the electrical

parts of the pump.

5.1 Discharge hose connec-

tion

The discharge hose is connected either

directly to the discharge port (9) or with

the multi adaptor (10) (secure discharge

hose with hose clamps, if necessary).

The check valve's flap (11) must open in

the direction indicated by the arrow. (The

marking "UP" must face the multi adap-

tor).

Note:

When using the multi adaptor cut

off any parts nor required, as they

reduce the flow unnecessarily.

5.2 Installation

x Required space is approx. 50 cm x

50 cm (for the float switch to operate

properly it must be able to move

freely).

x The pump must not be submerged

deeper into water then stated in the

"Technical Specifications".

x Place pump so that the suction inlet

can not be blocked by foreign

objects (stand on a base, if neces-

sary).

x Ensure sufficient upright stability.

Table of Contents

2. Please Read First!

3. Range of Application and

Media

4. Safety

5. Prior to Operation

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 38 39

Comments to this Manuals

No comments

Metabo TDP 7500 S User Manual Page 9

Comments to this Manuals

Related products and manuals for Tools Metabo TDP 7500 S