Metabo KNSE12-150 Use and Care Manual download pdf (Page 8)

ENGLISH

ENG

3.3 Safety Warnings Specific for Polishing:

Do not allow any loose portion of the polishing

bonnet or its attachment strings to spin freely.

Tuck away or trim any loose attachment

strings.

Loose and spinning attachment strings

can entangle your fingers or snag on the work-

piece.

3.4 Additional Safety Instructions

Use elastic cushioning layers if they have been

supplied with the abrasive and if required.

Observe the specifications of the tool or accessory

manufacturer! Protect the discs from grease or

impacts!

Accessories must be stored and handled with care

in accordance with the manufacturer's instruc-

tions.

The workpiece must lay flat and be secured

against slipping, e.g. using clamps. Large work-

pieces must be sufficiently supported.

Always wear protective goggles.

During machining, of metals in

particular, conductive dust can

form deposits inside the machine. This can lead to

the transfer of electrical energy onto the machine

housing. This can mean a temporary danger of

electric shocks. This is why it is necessary when

the machine is running to blow compressed air

through the rear ventilation slots of the machine

regularly, frequently and thoroughly. Here, the

machine must be held firmly.

We recommend using a stationary extractor

system and connecting a residual current circuit-

breaker (FI) upstream. When the polisher is shut

down via the FI circuit-breaker, it must be checked

and cleaned. See chapter

9 Cleaning for more information on cleaning the

motor.

Dust from materials such as lead-containing paint

and metal may be harmful to health. Contact with

or inhalation of the dust may cause allergic reac-

tions and/or respiratory diseases to the operator or

bystanders.

Certain kinds of dust are classified as carcino-

genic. Material containing asbestos must only be

treated by specialists.

- Where the use of a dust extraction device is

possible it shall be used.

- The work place must be well ventilated.

- The use of a dust mask of filter class P2 is

recommended.

Follow national requirements for the materials you

want to work with.

Materials that generate dusts or vapours that may

be harmful to health (e.g. asbestos) must not be

processed.

When working in dusty conditions, ensure that

ventilation openings are not blocked. If it becomes

necessary to remove dust, first disconnect the

power tool from the mains supply (use non-

metallic objects) and avoid damaging internal

components.

Damaged, eccentric or vibrating tools must not be

used.

Connect a FI circuit-breaker with max.

release current (30 mA) upstream when using the

machine outdoors!

Pull the plug out of the socket before making any

adjustments, converting or servicing the machine.

A damaged or cracked additional handle must be

replaced. Never operate a machine with a defec-

tive additional handle.

A damaged or cracked hand guard must be

replaced. Never operate a machine with a defec-

tive hand guard.

Symbols on the tool:

...........Class II Construction

V ...............volts

A...............amperes

Hz.............hertz

.../min .......revolutions per minute

~ ...............alternating current

..............alternating current /direct current

n ...............rated speed

See page 3 (please unfold).

1 Button for adjusting the hand guard

2 Hand protection

3Sliding

on/off switch

4 Additional handle / Additional handle with

vibration damping *

5 Speed adjustment wheel

6 Electronic signal indicator

7 Adjusting nut

8 Accessory

9Support flange

10 Spindle

11 Allen key

12 2-hole spanner

* depending on equipment/not in scope of delivery

4Overview

17026994_0610 KNSE 12-150 NAFTA.book Seite 8 Dienstag, 25. Mai 2010 11:43 11

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 35 36

Comments to this Manuals

No comments

Metabo KNSE12-150 Use and Care Manual Page 8

Comments to this Manuals

Related products and manuals for Power tools Metabo KNSE12-150