Metabo PE 12-175 Operations Instructions download pdf (Page 9)

ENGLISH en

7.1 Installing support plate and sanding

sheet

Only use the adjusting nut supplied with the

support plate.

Place the support plate on the spindle as shown in

the illustration. Screw on sanding sheet with

adjusting nut supplied with support plate. Lock the

spindle. Tighten sanding sheet with support plate

manually in a clockwise direction.

Release by hand or with a two-hole spanner if

necessary.

8.1 Setting speed

The speed can be preset via the setting wheel

(3)and is infinitely variable.

Positions 1-6 correspond approximately to the

following no-load speeds:

1.........700 rpm 4 .......1800 rpm

2.........1100 rpm 5 .......2000 rpm

3.........1500 rpm 6 .......2200 rpm

The VTC electronics make material-compatible

work possible and an almost constant speed, even

under load.

8.2 Switching On and Off

Switch on first, then guide the

accessory

towards the workpiece.

The machine must not be allowed to draw in

additional dust and shavings. When switching

the machine on and off, keep it away from dust

deposits. After switching off the machine, only place

it down when the motor has come to a standstill.

In continuous operation, the machine

continues running if it is forced out of your

hands. Therefore, always hold the machine with

both hands using the handles provided, stand in a

safe position and concentrate.

To switch on: Push the slide switch (2) forward.

For continuous activation, now tilt

downwards until it engages.

To switch off: Press the rear end of the slide switch

(2) and release it.

Motor cleaning: blow compressed air through the

rear ventilation slots of the machine regularly,

frequently and thoroughly. Here, the machine must

be held firmly.

The electronic signal display (4) lights up and

the load speed decreases. The coil temperature

is too high! Run the machine in idling until the

electronics signal indicator switches off.

The electronic signal display (4) flashes and

the machine does not start. The restart protection

is active. If the mains plug is inserted with the

machine switched on, or if the current supply is

restored following an interruption, the machine

does not start up. Switch the machine off and on

again.

Use only genuine Metabo accessories.

If you need any accessories, check with your

dealer.

For dealers to select the correct accessory, they

need to know the exact model designation of your

power tool.

See page 4.

A Polishing and sanding pads with Velcro

fasteners (for attaching polishing and sanding

accessories)

B Foam polishing pad, coarse with Velcro

fasteners (for buffing weathered paint)

C Foam polishing pad, fine with Velcro fasteners

(for polishing paint)

D Foam polishing pad, profiled with Velcro

fasteners (for polishing paint)

E Felt polishing disc, hard with Velcro fasteners

(for buffing paint, non-ferrous metals and

stainless steel sheets)

F Felt polishing disc, soft with Velcro fasteners

(for buffing paint, non-ferrous metals and

stainless steel sheets)

G Sheepskin polishing disc with Velcro fasteners

(for high-gloss polishing)

H Sheepskin polishing disc with cord drive (for

high-gloss polishing)

ISanding cloth with Velcro fasteners (for light

sanding, cleaning, degreasing)

J Cushioning disc with Velcro fasteners (for

sanding curved surfaces)

K Felt polishing disc with internal thread M 14

L Moltopren polishing disc with internal thread M

M Buffing disc 200 x 20 mm (for general polishing

work)

N Buffing disc 200 x 20 mm (for high gloss

polishing)

O Mounting shank for 2 buffing discs with flanges

and clamping nut

P Polishing paste (for metal and plastic)

For a complete range of accessories, see

www.metabo.com or the main catalogue.

8. Use

9. Cleaning

10. Troubleshooting

11. Accessories

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 23 24

Comments to this Manuals

No comments

Metabo PE 12-175 Operations Instructions Page 9

Comments to this Manuals

Related products and manuals for Straight grinders Metabo PE 12-175