Metabo TS 250 User Manual download pdf (Page 23)

23

ENGLISH

For rip and cross cuts in grown tim-

ber and particle board.

E TCT Saw Blade

250 x 2.8/1.8 x 30, 60 ATB teeth, 2

pinholes

For rip and cross cuts in grown tim-

ber and particle board.

F TCT Saw Blade

250 x 2.8/1.8 x 30, 80 ATB teeth, 2

pinholes

For rip and cross cuts in panels;

plastic, aluminium, copper extru-

sions and high-grade veneered

sheets.

G TCT Saw Blade

250 x 2.8/2.0 x 30, 80 square/trap-

ezoidal teeth

5° negative rake, 2 pinholes

General purpose blade for plastics,

thin-walled aluminium-, copper-,

brass- and steel extrusions as well

as for panels, laminates and

veneered sheets.

A

Danger!

Repairs to electric tools must

be carried out by qualified electri-

cians only!

Electric tools in need of repair can be

sent to the service centre of your coun-

try. Refer to the spare parts list for the

address.

Please attach a description of the fault to

the electric tool.

The machine's packing can be 100%

recycled.

Worn out power tools and accessories

contain considerable amounts of valua-

ble raw and rubber materials, which can

be recycled.

These instructions are printed on paper

produced with elemental chlorine-free

bleaching process.

A

Danger!

Before carrying out any fault service

or maintenance work, always:

1. switch machine OFF;

2. unplug power cable;

3. wait for saw blade to come to

standstill.

Check that all safety devices are

operational again after each fault

service.

Motor does not run

Undervoltage relay tripped by power fail-

ure:

x Restart machine.

No mains voltage

x Check cables, plug, outlet and

mains fuse.

Motor overheated, e.g. by a blunt saw

blade or chip build-up in the chip case:

x Remove cause for overheating, let

cool off for a few minutes. Then

press Reset button and restart

machine.

Stated top speed is not reached

Motor supply voltage too low:

x use a shorter extension cable or

extension cable with larger lead

cross section (t 1.5 mm

2

).

x Have power supply checked by a

qualified electrician.

Loss of cutting performance

Saw blade blunt (possibly tempering

marks on blade body):

x Replace saw blade (see chapter

“Maintenance”).

Dust spout blocked

No dust collector connected or suction

capacity insufficient:

x connect dust collector, or

x increase suction capacity (air speed

t 20 m/sec at chip ejection tube).

12. Repairs

13. Environmental Protection

14. Trouble Shooting

15. Technical specifications

Voltage V 230 (1a 50 Hz) 110 V (1a 50 Hz)

Wattage power input P1

power output P

2

kW

kW

2.0 kW S6 40%

1.2 kW S6 40%

1.55 kW S6 40%

0.84 kW S6 40%

Current draw A 9.6 15.5

Fuse protection min. A 16 (time-lag) –

Protection class IP 20 IP 20

Rated no-load speed (at 230V) min

-1

3950 3900

Cutting speed (at 230V) m/s 51.7 50.1

Saw blade diameter (outer) mm 250 250

Saw blade arbor bore diameter (inner) mm 30 30

Kerf width mm 2.8 2.8

Depth of cut with saw blade vertical

at 45° saw blade tilt

mm

mm

0 ... 77

0 ... 51

0...77

0...51

Dimensions length of saw table

width of saw table

height (with blade guard)

mm

mm

mm

645

755 (985)

430

645

755 (985)

430

Machine weight kg 32 32

Noise emission values, sawing,

A-sound pressure level L

pA

A-sound power level

LWA

dB (A)

dB (A)

83.6

97.9

83.6

97.9

1 2 ... 18 19 20 21 22 23 24 25 26 27 28 ... 46 47

Comments to this Manuals

No comments