Metabo SB18LTX Impuls 5.2 Use and Care Manual Page 12

  • Download
  • Add to my manuals
  • Print
  • Page
    / 76
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 11
ENGLISHen
12
Use only accessories which fulfil the requirements
and specifications listed in these operating instruc-
tions.
AChargers
B Battery packs with different capacities.
Use battery packs only with voltage suitable for
your power tool.
C Clamping ring with bit depot
Slide the clamping ring onto the machine flange
from the front (remove additional handle (1) if
necessary) and push together until they
engage.
D Bit clamping bush
E Chuck with Quick replacement system
F Bit holder with Quick replacement system
G Screw-type angle attachment with Quick
replacement system
For complete range of accessories, see
www.metabo.com or the main catalogue.
Repairs to electrical tools must be carried out by
qualified electricians ONLY!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Battery packs must not be disposed of with regular
waste. Return faulty or used battery packs to your
Metabo dealer!
Do not allow battery packs to come into contact with
water!
Only for EU countries: Never dispose of
power tools in your household waste! In
accordance with European Guideline 2002/
96/EC on used electronic and electric equipment
and its implementation in national legal systems,
used power tools must be collected separately and
handed in for environmentally compatible recycling.
Before disposal, discharge the battery pack in the
power tool. Prevent the contacts from short-
circuiting (e. g. by protecting them with adhesive
tape).
Explanatory notes on the information on page 3.
Changes due to technological progress reserved.
U =Voltage of battery pack
n
0
=No-load speed
Tightening torque for screwing:
M
1
=Soft screwing application (wood)
M
2
=Pulse torque
M
3
=Hard screwing application (metal)
M
4
=Adjustable torque
Max. drill diameter:
D
1 max
=in steel
D
2 max
=in softwood
D
3 max
=in concrete
s=Max. impact rate
m=Weight
(with smallest battery pack)
G=Spindle thread
D
max
=Chuck clamping range
Measured values determined in conformity with
EN 60745.
Direct current
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. Depending on the operating
conditions, the condition of the power tool or the
accessories, the actual load may be higher or lower.
For assessment purposes, please allow for breaks
and periods when the load is lower. Based on the
adjusted estimates, arrange protective measures
for the user e.g. organisational measures.
Vibration total value
(vector sum of three directions)
determined in accordance with EN 60745:
a
h, ID
=Vibration emission value
(impact drilling into concrete)
a
h, D
=Vibration emission value
(drilling into metal)
a
h, S
=Vibration emission level
(screwing without impact)
K
h, ...
=Uncertainty (vibration)
Typical A-effective perceived sound levels
:
L
pA
=Sound pressure level
L
WA
=Acoustic power level
K
pA
, K
WA
= Uncertainty
During operation the noise level can exceed
80 dB(A).
Wear ear protectors!
11. Repairs
12. Environmental Protection
13. Technical Specifications
Page view 11
1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 75 76

Comments to this Manuals

No comments