Metabo Compressor Pump Classic 8 User Manual download pdf (Page 12)

12

ENGLISH

4.2 Mains Connection

A

Danger! High voltage

Operate machine in dry environment

only.

Operate machine only on a power

source complying with the following

requirements:

− outlets properly installed, earthed

and tested;

− fuse protection in accordance

with the Technical Specifications.

Position power cable so it does not

interfere with the work and is not

damaged.

Always check to see that the machine

is switched OFF before plugging in.

Protect power cable from heat,

aggressive liquids and sharp edges.

Use only extension cables with suffi-

cient lead cross section (see "Techni-

cal Specifications").

Do not stop the compressor by

unplugging, but switch OFF using the

switch.

Unplug after use.

4.3 Generating compressed

air

1. Start compressor (28) and wait until

the max. tank pressure is reached

(compressor shuts off).

The tank pressure is indicated by

the tank pressure gauge (32).

2. Set pressure regulator (29) to

required working pressure. The cur-

rent working pressure is indicated

by the regulated pressure gauge

(31).

A

Caution!

The regulated pressure may not be

set higher than the max. working

pressure of the connected air tools!

3. Connect air hose to compressed air

outlet (30).

4. Connect air tool.

You are now ready to work with the

air tool.

5. Switch the compressor OFF (28), if

you do not continue working imme-

diately afterwards. Unplug after

switching OFF.

A

Danger!

Prior to all servicing:

− Switch Off.

− Unplug.

− Wait until the compressor has

come to a complete stop.

− Ensure the compressor and all air

tools and accessories connected

to it are relieved from pressure.

− Let the device and all air tools

and accessories used cool off.

After all servicing:

− Check to see that all safety

devices are operational.

− Make sure that no tools or other

parts remain on or in the

machine.

Repair and maintenance work other

than described in this section must

only be carried out by qualified spe-

cialists.

5.1 Periodic maintenance

A

Caution!

Überprüfen Sie am neuen Verdichter

die Anzugsmomente der Zylinderko-

pfschrauben (siehe "Technische

Daten") nach den ersten 50 und 250

Betriebsstunden.

Prior to each use

• Check air hoses for damage,

replace if necessary.

• Check all screwed connections for

tightness, tighten if necessary.

• Check power supply cable for dam-

age, if necessary have replaced by

a qualified electrician.

Every 50 operating hours

• Check air filter element (33) of com-

pressor pump, clean if necessary.

• Check oil level of pump at oil sight

glass (34), top up oil if necessary.

• Drain condensate from pressure

vessel (35).

A

Caution!

Das Kondenswasser enthält Öl und

muss über eine Problemstoff-Sam-

melstelle entsorgt werden.

Every 250 operating hours

• Replace air intake filter element of

compressor pump.

Every 500 operating hours

• Öl des Verdichters ablassen und

erneuern.

Every 1000 operating hours

• Have unit serviced by an authorized

service station. This will extent the

compressor's service life considera-

bly.

5.2 Machine storage

1. Switch unit OFF and unplug.

2. Release pressure from tank and all

connected air tools.

3. Store machine in such way that it

cannot be started by unauthorized

persons.

A

Caution!

Do not store machine unprotected

outdoors or in damp environment.

Do not lay device on its side for trans-

portation or storing.

A

Danger!

Prior to all servicing:

− Switch Off.

− Unplug.

30

31

28

29

32

5. Care and Maintenance

33

6. Trouble Shooting

34

35

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 31 32

Comments to this Manuals

No comments